ZKTeco QR500-WM QR Code and RFID Access Reader
QR code and 13.56MHz RFID card reader with Wiegand, RS485 and USB interfaces, powered from DC 12V or USB 5V for doors, gates and turnstiles.
Price on request
Available on backorder
RISYS can programme and prepare devices before delivery. Contact us for quantity and project details.
Wholesale and project supply — up to 45% off











Up to 45% off wholesale supply.
Overview
The ZKTeco QR500-WM is a QR code and RFID card reader built for doors and gates where visitors arrive with a code on their phone and staff carry a card. What sets it apart within this ZKTeco family is its power design: it accepts DC 12V (+/-5%), the low-voltage feed common to door hardware and access panels, and it can also run from USB 5V. That dual input lets you mount it at an entrance and wire it into the existing low-voltage run, or power it from a USB port at a desk during setup and testing. It reads QR codes at 5 cm or more and 13.56MHz cards at 4 cm or more, then hands each credential to your access controller over Wiegand or RS485, with USB as a third interface.
What the ZKTeco QR500-WM does in practice
The reader is a credential front end. It does not decide who opens the door; it reads what is presented and passes the result to the controller or system behind it. A visitor holds a phone screen or a printed slip with a QR code in front of the reading window, the reader decodes it, and the code travels down the Wiegand or RS485 line. A staff member taps a card instead, and the same path is used. Keeping the decision logic in one place means adding a QR500-WM to an existing site does not require rebuilding the permission database.
On the card side it covers the 13.56MHz family under ISO/IEC 14443A, including Mifare Ultralight, DESFire EV1, NTag and S50/S70 cards. In practice one reader can serve a site that issued S50 staff cards years ago and is now moving sensitive areas to DESFire EV1, without swapping hardware at every door during the transition. NTag and Ultralight support suits low-cost temporary passes for contractors or event guests.
The rated read distances are 5 cm or more for QR codes and 4 cm or more for cards, so mount the reader at a height where people can bring a phone or card close to the window comfortably, including wheelchair users.
Where it fits in Saudi facilities
Office towers in Riyadh and Jeddah that send visitor QR invitations from a reception system can place the QR500-WM at lobby gates or meeting-floor doors, so a guest walks in with the code on their phone while employees keep using their existing cards. Hospitals and clinics can apply the same pattern during visiting hours by handing families a printed QR slip at the front desk. Universities and training centres with a mix of students, staff and short-term trainees can use DESFire EV1 for long-term cards and NTag for temporary passes. Residential compounds can issue single-visit QR codes to delivery drivers and maintenance contractors instead of lending out cards that rarely come back.
The rated operating range is -10 C to 50 C with humidity between 20% and 80%, which suits indoor lobbies and shaded entrances. For a gate exposed to summer sun in the Eastern Province or an open logistics yard, plan a canopy or enclosure that keeps the unit inside that range. Storage is rated from -20 C to 80 C, so spare units can be kept in a site store.
QR500-WM or ZK8500R ID: choosing within the family
The two readers in this group solve different problems. The QR500-WM is a door-side device: it takes 12V DC from the access system supply, reports over Wiegand or RS485, and reads QR codes alongside cards. The ZK8500R ID is a desktop enrolment unit that runs only from a computer’s USB port, reads optical fingerprints, low-frequency EM proximity cards and Mifare cards, and connects to Windows software rather than to a door controller.
Choose the QR500-WM when visitors need QR entry at a door or gate, or when you want DESFire EV1 and NTag cards working at entry points. Choose the ZK8500R ID when you need to capture fingerprints or register cards at an office computer. The two often sit at opposite ends of one workflow: enrolment at a desk, verification at a door. Because the QR500-WM is a 13.56MHz card reader, check your card stock first if your site still issues older low-frequency proximity cards.
Deployment notes
Plan a stable 12V DC feed within the +/-5% tolerance, using a regulated supply that holds that voltage, especially when the same supply also drives electric locks. Use Wiegand for a direct link to a controller that accepts Wiegand readers, and RS485 where the controller expects a serial bus. USB 5V lets an installer power the reader from a laptop to check card and QR reads before it goes on the wall. Before ordering, confirm the card types already in use on your site, and that your visitor management platform issues QR codes your controller can match against its permissions.
Technical Specifications
- Brand
- ZKTeco
- Authentication Method
- QR code; RFID card (ISO/IEC 14443A, Mifare Ultralight, DESFire EV1, NTag, S50/S70)
- Connectivity
- Wiegand, RS485, USB
- Device Type
- QR code and RFID card reader
- Model
- QR500-WM
- Power
- DC 12V (+/-5%), USB 5V
Frequently Asked Questions
Which credentials does the ZKTeco QR500-WM read?
It reads QR codes from a phone screen or printed slip, and 13.56MHz RFID cards under ISO/IEC 14443A, including Mifare Ultralight, DESFire EV1, NTag and S50/S70.
How does it connect to an access controller?
It outputs over Wiegand or RS485, and also provides a USB interface.
What power does it need?
It runs on DC 12V (+/-5%) or from USB 5V, which is handy for bench testing before installation.
What is the read distance?
The rated read distance is 5 cm or more for QR codes and 4 cm or more for RFID cards.
Is it suitable for outdoor entrances?
Its operating range is -10 C to 50 C with humidity between 20% and 80%, so it suits indoor and shaded entrances; for gates in direct sun, plan a canopy or enclosure.

Browse ZKTeco access control and time attendance equipment in one place: face and fingerprint terminals, door controllers, card readers, electric locks, hotel locks and vehicle barriers for offices, hotels and compounds across Saudi Arabia. ZKTeco is a Chinese biometrics manufacturer
Browse brand productsDelivery across Saudi Arabia
Clear warranty
Some devices or frequencies may require a permit or approval depending on the intended use and the regulations in force in the Kingdom. Requirements are clarified before project orders are fulfilled.
Customer Reviews
No ratings yet for this product
Only logged in customers who have purchased this product may leave a review.
Related Products
ZKTeco ZK-8500 USB Fingerprint and Card Enrollment Reader
On backorder
ZKTeco SF300 Fingerprint Access Control Terminal
On backorder
ZKTeco ZK-QR600-V-E QR and EM-Marine RFID Reader
On backorder
ZKTeco ZK-SC503 RFID Standalone Access Control Terminal
On backorder





Reviews
There are no reviews yet.