ZKTeco ZK-WRF100 MF Wireless Mifare Access Reader
Wireless Mifare UID reader with a receiving module, encrypted 433MHz communication and Wiegand W26/W34 output. The reader uses 4.5V while the receiver requires DC 12V.
104.40 SAR excl. VAT
Available on backorder
RISYS can programme and prepare devices before delivery. Contact us for quantity and project details.
Wholesale and project supply — up to 45% off











Up to 45% off wholesale supply.
Overview
ZKTeco WRF100 MF combines a wireless Mifare card reader with a data receiving module, making the separation between the card presentation point and the receiver central to the installation. The reader operates at 4.5V, while the receiver uses DC 12V, so each side needs its own power planning. For a Saudi facilities manager reviewing a card access project, this is a practical distinction: choosing the reader also means choosing where its receiver will sit and how the access system will accept its output. The unit reads Mifare UID credentials, communicates wirelessly at 433MHz and supports Wiegand, bringing the card reading point into a controller based access arrangement.
ZKTeco WRF100 MF at the card presentation point
The credential technology is 13.56MHz Mifare UID, with a reading distance of up to 2.5cm. Users therefore present their cards close to the reader rather than treating it as a distant identification device. Place the reader where staff can reach it naturally as they approach the controlled area. At an office entrance, a warehouse staff access point or a service corridor, that placement gives the facilities team a clear place to direct users and a defined location for testing card presentation during commissioning.
Its capacity is 1,000 users. Compare that capacity with the population assigned to the intended access point, including the staff groups that will use it during different shifts. A personnel count and a card technology check address different parts of the selection: the population must fit the capacity, and the credentials must match Mifare UID reading. A site already issuing cards should check the credential type before treating existing badges as suitable for this reader.
Wireless transmission and the controller connection
The wireless emission distance is up to 30m. Use that limit when reviewing the proposed reader and receiver locations, then test communication at the actual installation positions before completing the work. Wireless communication is encrypted. For the project team, the relevant installation task is to verify the link between these parts and the receiving side’s integration with the access system. The radio link and the credential reading distance serve different purposes; a usable wireless path does not change how closely a user presents a card.
Wiegand formats W26/W34 provide the interface options for integrating the receiving side. Ask the installer to confirm the controller’s supported format and align the configuration with the selected credential arrangement. Include a real card presentation in the acceptance test so the team verifies the path from reading through reception to the controller. This sequence is useful when commissioning staff entrances in commercial offices, logistics facilities or education buildings, where several teams may share responsibility for credentials, cabling and access policy.
A separate power plan for each side
The reader’s 4.5V supply and the receiver’s DC 12V supply are distinct requirements. Mark them separately in the installation schedule so the technician prepares the correct supply for each part. Review receiver positioning together with its controller connection, while reviewing the reader position together with card presentation and the wireless path. This division gives the contractor concrete tasks to check before mounting and helps the buyer assess whether the proposed installation layout matches the device’s architecture.
Position within the access reader family
The WRF100 MF selection turns on its reader and receiving module arrangement. By comparison, ZK4500 is a USB optical fingerprint scanner connected to a PC. A desk based fingerprint capture task therefore points toward ZK4500, while a project requiring wireless Mifare reading and a Wiegand interface points toward WRF100 MF. FR1300 lists DC power, but WRF100 MF specifically separates power requirements between reader and receiver. Keep those installation roles clear when comparing models rather than selecting solely because the products share an access reader category.
Environmental review and handover
The ingress protection rating is IP66, with an operating temperature range of -20°C to +60°C and operating humidity of 0%-86%. Compare these limits with the proposed location, especially around service entrances and areas exposed to changing environmental conditions. During handover, verify card reading at the installed height, the wireless connection at the chosen positions, the Wiegand format and the correct power supply on each side. These checks give the facilities team a practical acceptance sequence tied to the equipment it will operate.
Technical Specifications
- Brand
- ZKTeco
- Authentication Method
- 13.56MHz Mifare UID
- Capacity
- 1,000 users
- Connectivity
- 433MHz, Wiegand
- Device Type
- wireless reader and data receiving module
- Model
- ZK-WRF100 MF
- Power
- Reader 4.5V; receiver DC 12V
Frequently Asked Questions
Which cards does WRF100 MF read?
It reads 13.56MHz Mifare UID cards at a distance of up to 2.5cm.
Do the reader and receiver use the same supply?
The reader uses 4.5V; the receiver requires DC 12V. Plan their supplies separately.
How does it connect to an access system?
It uses encrypted 433MHz wireless communication and supports Wiegand formats W26/W34.
What are its user capacity and wireless distance?
Capacity is 1,000 users, and wireless emission distance is up to 30m. Test the link at the intended installation positions.

Browse ZKTeco access control and time attendance equipment in one place: face and fingerprint terminals, door controllers, card readers, electric locks, hotel locks and vehicle barriers for offices, hotels and compounds across Saudi Arabia. ZKTeco is a Chinese biometrics manufacturer
Browse brand productsDelivery across Saudi Arabia
Clear warranty
Some devices or frequencies may require a permit or approval depending on the intended use and the regulations in force in the Kingdom. Requirements are clarified before project orders are fulfilled.
Customer Reviews
No ratings yet for this product
Only logged in customers who have purchased this product may leave a review.
Related Products
ZKTeco SLK20R USB Fingerprint Scanner
On backorder
ZKTeco ZK-SC503 RFID Standalone Access Control Terminal
On backorder
ZKTeco ZK-InBio260Pro Two-Door Biometric Access Panel
On backorder
ZKTeco ZK-InBio160Pro Biometric Access Control Panel
On backorder





Reviews
There are no reviews yet.